Titanium Tools and Equipment Inc

For easy puller, easy puller II, and the pet slide hammers.

Straight keys can be welded very close together so are ideal for strong pulls on rockers. Weld keys according to the strength of pull required. The...

Meets the requirements of Aston Martin The Big Leather Welding Blanket is a 70 x 70 inches (5ft 8” x 5ft 8”) welding blanket that gives you big pro...

Twisted keys are ideal for press lines and curved areas like gas tanks. Weld keys according to the strength of pull required. Can be welded with mi...

The special Miracle system ground. It can replace the ground on older models or new models. The ground has 3 ways of attaching to the panel. The t...

Meets the requirements of Aston Martin The Door Trim Leather Welding Blanket is a pair of one left and one right hand welding blankets for protecti...

The carbon rod allows you to heat up the metal panel without leaving the job to get a torch. The heat can be controlled by touching the metal surfa...

Yellow glue sticks to be used with the Miracle System super glue gun or any other quality glue gun. Packing Unit: 50 pieces.

0.8 mm wave staple for the hot stapler. Pack of 100pcs.

The point shrinking tip allows you to put down high spots and shrink where required often allowing you to remove “oil canning” without burning the ...

The bit holder allows you to hold all three key types and attach them to the panel. MB-1, MB-2 and MB-3 fit in the slot and hold the key tightly.

Miracle aluminum bit straight type with Lines. The lines allow you to cut the key at the correct length for even pulls.

Delicate and precise pulling control can be applied for small dent repair anywhere on the vehicle. Size options available for small, medium, and ...

0.8 mm flat staple for the hot stapler. Pack of 100pcs.

0.6 mm flat staple for the hot stapler. Pack of 100pcs.

Replacement Center Shaft for the Miracle System Easy Puller 10Z.

These premium heavy-duty Leather Welding Gloves is designed for a wide range of welding processes including MIG, TIG, and Stick. Offers good protec...

Optimize your dent pulling with our versatile glue pads in sizes; small, medium, and large. They can be used for large dent repair. Features: ...

For best results, please use these glue sticks with the Miracle System Glue Kit. Packing Unit: 15 pieces.

The airopower deluxe trolley is specially designed to store the airopower system. A standard kit fits on the top shelf and all the airopower access...

Catalogue | Videos This is a 53 piece Accessory Kit ONLY. The Airopower Standard Kit needs to be purchased separately.   The Mini Frame Machine ...

Replacement Handle for the Miracle System Easy Puller 10Z.

The Airopower flat base is used in big and flat areas of the vehicle like the trunk, hood, and engine compartment.

Suction cup with vacuum pump and leakage indicator Concave pod for curved surfaces Loading capacity: 20kg / 44lbs Cup diameter: 5 inches.

Yellow Glue Sticks works best with Miracle System glue gun or any other quality glue gun. Packing Unit: 15 pieces.

h5> Features: Improves Productivity Reduces damage without removing paint Great for aluminum panels Can be used with existing pulling tools or ...

These washers can be welded with minimum electric current, resulting in very little damage to the panel Can be used for strong places like; quarte...

This aluminum bit can be used with the easy puller for small dents. The round hole works with the limited travel of the easy puller.

0.8 mm outside corner staple for the hot stapler. Pack of 100pcs.

0.6 mm wave staple for the hot stapler. Pack of 100pcs.

The Airopower knock pin is used for holding clamps, pins, and adapters in place.

Stud weld and dent pull like a pro with the Miracle Multi-Earth Ground Clamp. Key Features A wider grounding area with a welding tip increases out...

Keep Your Spot Welder Running Like NewProtect your investment and minimize downtime with a Titanium Tools & Equipment Spot Welder Maintenance C...

Product Description Shield your Airopower cart and accessories with the EP-COVER, a custom-fit protective cover that guards against weather, dust,...

The Miracle Multi Hammer is a premium panel repair hammer made of a rare metal. Functions and Features Special Curved head: Special curved head l...

The Miracle System light punch comes in 3 different shapes for knocking down high spots. It is 110mm long and 12mm in diameter.

These glue pads are flexible and especially effective for line repair. They come in sizes small and large. Features: for dent line repair re...

Hook for large dent pulling using any of these Miracle System dent pullers: strong puller, lever puller, and hand puller.

Hook for large dent pulling using any of these Miracle System dent pullers: strong puller, lever puller, and hand puller.

Hook for single pull using any of these Miracle System dent pullers: strong puller, lever puller, and hand puller.

Hook for single pull using any of these Miracle System tools: easy puller, easy puller II, easy puller III, and Miracle pet hammer slide kit.

Easy puller hook for aluminum bits MAB-PA and MAB-PSP.

For those looking to weld aluminum studs to aluminum panels, this is the ALU-6. This aluminum stud welder kit can be added to any Steel System or p...

The Miracle shaft kit is made of a special compounded steel shaft and is used for pulling out lines or scrapes. Technical Data MF-5-1, L type 450m...

Replacement ground bit for Miracle ground clamp.