Products

Standalone 4″ dock. Unique design combines a center pulling point together with a anchoring/feeding solution.

Replacement spindle for 4″ Removal Dock.

Pack of 9 high tack 3M removal pads for quick temporary fastening of the Removal Dock.

ABS Plastic Round Rod, 1/8” - Black 1/2 lb for Nitrogen Plastic Welder.

Aluminum Pulling Eye/Pull Key. Features Pack of 12 Reusable Thread on to aluminum studs to pull dents from aluminum panels

M4x10mm Aluminum Weld Stud (Pack of 50).

M4x10mm Aluminum Weld Stud (Pack of 500).

M4x16mm Aluminum Weld Stud (Pack of 500).

The bit holder allows you to hold all three key types and attach them to the panel. MB-1, MB-2 and MB-3 fit in the slot and hold the key tightly.

High Performance cutting oil for drill bits, milling cutters, grinding discs, and saw blades. Proven to increase the service life of milling cutter...

The carbon rod allows you to heat up the metal panel without leaving the job to get a torch. The heat can be controlled by touching the metal surfa...

Stainless Steel Brush, Pack of 3 Part Number: 50-0580-3PK

Features: Clear, non-staining gel leaves no residue eliminating clean-up Safe, non-toxic, harmless to skin and odorless; convenient trigger spray ...

Very flexible, high mechanical load capacity, special steel with "smooth" surface, no scratches or damages on paint or trimmings. 1 roll of cutting...

Easy puller hook for aluminum bits MAB-PA and MAB-PSP.

It is a replacement special bit for the Easy Puller III.

High strength glue sticks. 20 pieces per pack.

A pack of 2 electrodes copper washers for the InvertaSpot GT Automatic.

This high tef oil is great for lubricating the cable that attaches to Easy Puller I and II for smooth operation and less wear of the clips and tool...

Xpress 800 special oil for service and maintenance of the modules power-pack - bind-rivet adapters - PushPull. Technical Data: Packing unit: 1 pc.C...

i5 gun replacement cooling hose kit. It comes with hoses and fittings as can be seen in the pictures.

It replaces the standard lever puller hook with this hook for pulling on individual aluminum bits.

This aluminum bit can be used with the easy puller for small dents. The round hole works with the limited travel of the easy puller.

This aluminum bit is used for body lines. The lines allow you to cut the key at the correct length for even pulls.

Miracle aluminum bit straight type with Lines. The lines allow you to cut the key at the correct length for even pulls.

This tip is to be used in the steel welder (SMS-7Q) for shrinking aluminum. The MS-U-B17 heats up and can be used to shrink aluminum panels. Techni...

Rubber head cover only, hammer not included. To be used with Miracle Hammer Rubber Face Horizontal Peen (MHSG-03) and Miracle Hammer Rubber Face Ve...

Miracle Special Aluminum Bit for Easy Puller.

Miracle Special Aluminum Bit Screw Type with Lines.

Miracle Special Aluminum Bit Straight Type with Lines.

Non Adhesion Paper for FlexiTherm Heating System. Place it directly on patty or filler. Protects the heating pads from sticking or getting dirty. T...

Polypropylene welding rods, 3/16" for Nitrogen Plastic Welder.

The point shrinking tip allows you to put down high spots and shrink where required often allowing you to remove “oil canning” without burning the ...

Polypropylene Sheet for Nitrogen Plastic Welder.

Polypropylene Strip, 3/4” x 1/16” - Natural - 1/2 lb for Nitrogen Plastic Welder.

Replacement bolt for the Removal Dock Base.

The roll patching tip allows you to repair small torn areas on a panel quickly and easily.

Twisted keys are ideal for press lines and curved areas like gas tanks. Weld keys according to the strength of pull required. Can be welded with mi...

Technical Data: Diameter: 6 mm Packing unit:  50 pcs. Material: HSS, cobalt

Technical Data: Diameter: 6.7 mm Packing unit:  50 pcs. Material: HSS, cobalt

Technical Data: Diameter: 8 mm Packing unit:  50 pcs. Material: HSS, cobalt Old Part Number: 700296

For easy puller, easy puller II, and the pet slide hammers.

The spot welding tip allows you to tack thin patches for repair quickly and easily prior to MIG welding.

Straight keys can be welded very close together so are ideal for strong pulls on rockers. Weld keys according to the strength of pull required. The...

These washers can be welded with minimum electric current, resulting in very little damage to the panel Can be used for strong places like; quarte...

TPO Strip, 3/8” x 1/16” - Gray 1/2” lb for Nitrogen Plastic Welder.

Pro Spot trigger switch.

Universal welding ribbon, 3/8” x 1/16“ - black 1/2 lb for Nitrogen Plastic Welder.