Titanium Tools and Equipment Inc

Straight keys can be welded very close together so are ideal for strong pulls on rockers. Weld keys according to the strength of pull required. The...

For easy puller, easy puller II, and the pet slide hammers.

AIROPOWER BROCHURE Airopower is a pneumatic 5.25 tons push and pull ram that eliminates the problems of leaking porta powers yet is far more versa...

Twisted keys are ideal for press lines and curved areas like gas tanks. Weld keys according to the strength of pull required. Can be welded with mi...

The special Miracle system ground. It can replace the ground on older models or new models. The ground has 3 ways of attaching to the panel. The t...

Optimize your dent pulling with our versatile glue pads in sizes; small, medium, and large. They can be used for large dent repair. Features: ...

The point shrinking tip allows you to put down high spots and shrink where required often allowing you to remove “oil canning” without burning the ...

The bit holder allows you to hold all three key types and attach them to the panel. MB-1, MB-2 and MB-3 fit in the slot and hold the key tightly.

Miracle aluminum bit straight type with Lines. The lines allow you to cut the key at the correct length for even pulls.

0.8 mm wave staple for the hot stapler. Pack of 100pcs.

0.8 mm flat staple for the hot stapler. Pack of 100pcs.

0.6 mm flat staple for the hot stapler. Pack of 100pcs.

The airopower deluxe trolley is specially designed to store the airopower system. A standard kit fits on the top shelf and all the airopower access...

Description Device Receptacle Sqaure Box Square Cover Electrical hook up kit (Eaton Arrow Hart Power device receptacle, square box, and square...

The Miracle System light hammer is a must have hammer for paintless dent removal. It is made of reinforced plastic, 240mm long, and only weighs...

The Miracle System light punch comes in 3 different shapes for knocking down high spots. It is 110mm long and 12mm in diameter.

Effective for removing glue pads without scratching the car paint. Made with reinforced plastic. It is 270mm long with a tip width of 25mm.

These glue pads are flexible and especially effective for line repair. They come in sizes small and large. Features: for dent line repair re...

Delicate and precise pulling control can be applied for small dent repair anywhere on the vehicle. Size options available for small, medium, and ...

Hook for large dent pulling using any of these Miracle System dent pullers: strong puller, lever puller, and hand puller.

Hook for large dent pulling using any of these Miracle System dent pullers: strong puller, lever puller, and hand puller.

Hook for single pull using any of these Miracle System dent pullers: strong puller, lever puller, and hand puller.

Hook for single pull using any of these Miracle System tools: easy puller, easy puller II, easy puller III, and Miracle pet hammer slide kit.

The Miracle System super glue gun is a high performance glue gun for professional use that melts the glue sticks efficiently and bonds the glue pad...

Easy puller hook for aluminum bits MAB-PA and MAB-PSP.

For those looking to weld aluminum studs to aluminum panels, this is the ALU-6. This aluminum stud welder kit can be added to any Steel System or p...

The Miracle shaft kit is made of a special compounded steel shaft and is used for pulling out lines or scrapes. Technical Data MF-5-1, L type 450m...

The Miracle line puller is the most ideal method for line repairs. The long frame and sliding hook gives you the best position to pull a line. It i...

Replacement ground bit for Miracle ground clamp.

Used with brass pipe to repair the Miracle ground clamp, MME-00.

Used with shrink tube to repair the Miracle ground clamp, MME-00.

The Airopower pull hook is used with the 2 meters chain and is used for chain pulls.

The Airopower wedge head is used for pointed areas, bars, and corners.

The Airopower v-base is used on hard areas of the vehicle like the engine support, front rails, and pillars.

The Airopower plunger toe is used together with the collar toe for pushing and pulling vehicle parts like the door space.

The Airopower collar toe is used together with the plunger toe for pushing and pulling vehicle parts like the door space.

The Airopower flat base is used in big and flat areas of the vehicle like the trunk, hood, and engine compartment.

The Airopower serrated saddle is used to push flat areas on the vehicle.

The Airopower female connector can be attached to the front (piston) of the Airopower ram as an extension or a connector. It is used to connect att...

The Airopower male connector can be attached to the rear connector of the Airopower ram as an extension or a connector. It is used to connect attac...

The difference between the Miracle Light Basic kit  and the other Miracle Light kit is the type of stud welder and easy puller the Miracle Light Ba...

Miracle Light Plus kit comes with an ESA inspected manual-automatic stud welder (MS-6) complete with a slide hammer, accessory box, Miracle ground,...

The difference between the Miracle Essentials Basic kit  and the other Miracle Essentials kit is the type of stud welder and easy puller the Miracl...

Miracle Essentials Plus kit comes with an ESA inspected manual-automatic stud welder (MS-6) complete with a slide hammer, accessory box, Miracle gr...